Official GIGABYTE Forum

GA-X170-EXTREME ECC - Error Code 55

GA-X170-EXTREME ECC - Error Code 55
« on: May 28, 2016, 09:35:56 am »
Hey, i've built a new pc with these specs.

- Intel Xeon 1275-V5
- DDR 4 ECC 16Gb 2133mhz x1
- Motherboard in the topic title
- Noctua Custom Cooler

The PC doesn't post and the bios error code led says 55, which is memory Initialization. The same happens if i run with no RAM inserted, as it should.

Did anyone have the same issues?
Could it be not just the ram but the Cpu?
Any suggestion?

PS: I'm fairly sure i set up everything correctly. I've built many other pcs.

Re: GA-X170-EXTREME ECC - Error Code 55
« Reply #1 on: May 28, 2016, 04:18:59 pm »
Hello,

It might be the memory configuration so try using 4GB non-ECC unbuffered ddr4, if it posts you will know the CPU is fine.

1 Rank x 8
2 Rank x 8

There is a limitation on the memory ranks, see the compatibility chart.
« Last Edit: May 28, 2016, 08:12:44 pm by ElectroStingz »
My PC is evolving

Re: GA-X170-EXTREME ECC - Error Code 55
« Reply #2 on: June 07, 2016, 09:56:01 am »
Hello,

just as a data point: My GA-X170-EXTREME ECC works fine with 2 sticks of Kingston ValueRAM KVR21E15D8/16 (each 16 GB ECC DDR4 2133).
GA-X170-EXTREME ECC rev. 1.0, BIOS F1, Intel Xeon E3-1245 v5, 2 * Kingston ValueRAM KVR21E15D8/16, Samsung 850 Evo 500 GB,WD Red 6 TB, Noctua NH-D15, be quiet! Straight Power 10 500 W CM, Fractal Design Define R5 PCGH Edition, Ubuntu 16.04 LTS, Windows 10 Pro 64 bit

Re: GA-X170-EXTREME ECC - Error Code 55
« Reply #3 on: January 04, 2017, 02:56:15 pm »
Hi there,

Just wondering, but which ECC memory modules were you trying to use? I've been having this same issue with Crucial's CT4K16G4RFD4213 modules. I too get debug code 55, though how long it takes to appear depends on how many memory modules are inserted.

What I've tried first:

a) Powering on with two DIMMs in slots 1 and 3 only.
b) Powering on with two DIMMs in slots 2 and 4 only.
c) Powering on with a single DIMM in slot 1.
d) Powering on with a single DIMM in slot 3.
e) Powering on with no DIMMs at all.
f) Re-seating the CPU to be sure it's in place properly, including the cooler.
g) Switching between single and double BIOS/UEFI.
h) Clearing the CMOS.
i) Double-checking all the PSU cables are in place, especially the ATX and CPU ones.
j) Powering on with less hardware attached to the PSU. (Unplugged hard disks, SSD, etc.)

I was then told this was appearing because there was no GPU installed. (I thought that the Intel Xeon E3-1270 v5 CPU had one integrated but does not.) Installing a GPU made no difference though.

Here is a video of what was happening: https://www.dropbox.com/s/z3s582m9s53ouh7/20161216_125436.mp4?dl=0

I was then told to try the following, none of which made a difference:

a) Remove the RAID controller from the 2nd PCI-E 16x slot.
b) Move the GPU from PCI-E 16x slot 1 to slot 2.
c) Try each memory module alone in DIMM slot 1.
d) Check for any bent pins on the CPU socket. (Didn't see any, attached photos.)

Currently I've been asked if I have any spare memory kits, which I don't because DDR4 ECC memory is not cheap. I'm wondering if this memory module will be sufficient to verify if the Crucial memory kit is at fault.

https://www.amazon.co.uk/d/RAM/Transcend-Memory-4GB-TS512MLH72V1H-2133MHz-CL15-DDR4/B00VQPG3QS