Official GIGABYTE Forum

DDR3 2000 or 1333 for GA-X58A-UD5

DDR3 2000 or 1333 for GA-X58A-UD5
« on: January 01, 2011, 03:38:37 am »
Hello all,

I'm planning a new build around the GA-X58A-UD5 mobo.  I see that the DDR3 2200 modules are expensive hard to find, especially on NewEgg.  The question is, if I drop three DDR3 2000 modules in there, are those going to clock down to 1333 on me?  I see the specs for this mobo are documented as 2200/1333/1066/800.  Am I better off putting DDR3 1333 in there and saving the cash?  Thanks!

Re: DDR3 2000 or 1333 for GA-X58A-UD5
« Reply #1 on: January 01, 2011, 05:15:17 am »
OK so the memory controller on the Core i7-950 runs at 1066 Hz, and I can't run higher than that without overclocking the CPU as well.  Is this true?  If so, I guess I answered my own question and am looking at going the PC3 8500 route.

Dark Mantis

  • *
  • 18405
  • 414
  • 10typesofpeopleoneswhoknow binaryandoneswhodont
    • Dark Mantis
Re: DDR3 2000 or 1333 for GA-X58A-UD5
« Reply #2 on: January 01, 2011, 10:29:57 am »
Hi and welcome to the Gigabyte Forum.

What you said is fairly much correct and the standard speed as governed by the JEDEC standard exists but it is of course possible to go over that albiet by overclocking the memory/memory controller on the CPU. I am using corsair Dominator 1600 Mhz in my UD7 and of course that is overclocked also but I am not overclocking my processor in the normal sense. I am just using the XMP that comes attached to the memory to increase the speed. The same could be achieved by manually making the same changes in the BIOS.
Gigabyte X58A-UD7
i7 920
Dominators 1600 x6 12GB
6970 2GB
HX850
256GB SSD, Sam 1TB, WDB320GB
Blu-Ray
HAF 932

Gigabyte Z68X-UD5-B3
i7 3770K
Vengeance 1600 16GB
6950 2GB
HCP1200W
Revo Drive x2, 1.5TB WDB RAID0
16x DLRW
StrikeX S7
Full water cooling
3 x 27" Iiy

JakeF150

  • 20
  • 0
Re: DDR3 2000 or 1333 for GA-X58A-UD5
« Reply #3 on: January 02, 2011, 09:52:27 am »
No need to overclock the CPU to run the memory at a higher rate.  Just up the multiplier on the memory.  Memory will default to 1066 x 10, just increase to x12 for 1333, and x14 for 1666.  Good luck attempting to run at 2000.  Could never get my 6x2G near that, but run at 1666 just fine.  I would say get some good 1600 memory.

Dark Mantis

  • *
  • 18405
  • 414
  • 10typesofpeopleoneswhoknow binaryandoneswhodont
    • Dark Mantis
Re: DDR3 2000 or 1333 for GA-X58A-UD5
« Reply #4 on: January 02, 2011, 12:38:17 pm »
No need to overclock the CPU to run the memory at a higher rate.  Just up the multiplier on the memory.  Memory will default to 1066 x 10, just increase to x12 for 1333, and x14 for 1666.  Good luck attempting to run at 2000.  Could never get my 6x2G near that, but run at 1666 just fine.  I would say get some good 1600 memory.

No I am not suprised that you didn't manage to get all 6 modules to 2000 MHz. It is always a lot harder to reach the higher speeds when all slots are full.
« Last Edit: January 02, 2011, 12:38:54 pm by Dark Mantis »
Gigabyte X58A-UD7
i7 920
Dominators 1600 x6 12GB
6970 2GB
HX850
256GB SSD, Sam 1TB, WDB320GB
Blu-Ray
HAF 932

Gigabyte Z68X-UD5-B3
i7 3770K
Vengeance 1600 16GB
6950 2GB
HCP1200W
Revo Drive x2, 1.5TB WDB RAID0
16x DLRW
StrikeX S7
Full water cooling
3 x 27" Iiy