Official GIGABYTE Forum

Questions about GIGABYTE products => Motherboards with AMD processors => Topic started by: wizeone on June 13, 2011, 03:26:38 pm

Title: m68m-s2p rev 2.3
Post by: wizeone on June 13, 2011, 03:26:38 pm

ok so i have a gigabyte board ( http://us.test.giga-byte.com/Support/Motherboard/CPUSupport_Model.aspx?ProductID=3505&ver= ) that is supposed to have gigabit lan.

when i go into the settings for the adapter->advanced->speed/dupex settings it only gives me the options of:
10 mb full
10 mb half
100mb full
100mb half
auto negotiation
autoneg for 100fd
autoneg for 100hd
autoneg for 10fd
autoneg for 10hd

which one of these is the gigabit setting??  or did gigabyte lie on everything?? the adapter says Nvidia nForce 10/100/1000 mbps ethernet.

i'm lost on this.

Title: Re: m68m-s2p rev 2.3
Post by: F5BJR on June 13, 2011, 03:58:29 pm

*
If you have an USB HUB , test with another , i have found stupids compatibility problems with this

by exemple :

1 - D-LINK DGS1008D OK in GigaBits mode

2 - TrendNet TEG-S8/AG not Ok in GigaBits mode with all my computers

Pierre

Title: Re: m68m-s2p rev 2.3
Post by: Dark Mantis on June 13, 2011, 04:01:33 pm

Hi and welcome to the Gigabyte Forum.

Have you installed he latest BIOS version for your board ?

What about the LAN chip drivers ?

What are you connecting to that is Gigabit supportive ?

Title: Re: m68m-s2p rev 2.3
Post by: F5BJR on June 13, 2011, 04:05:35 pm

*
For me my problems are not with drivers because LAN cards or HUB Leds are in 100 Mbits mode and not in 1 GBits  at BIOS Startup !!

If i remember problem are with Marvell ports

Pierre

* tested just at this time my ASUS P5E WS with 2 * 88E8056

one port run in GigaBits mode and the other in 100 MBits with the TrenNet HUB !!

Title: Re: m68m-s2p rev 2.3
Post by: wizeone on June 13, 2011, 04:40:53 pm

have not done a bios flash yet.

it is connected via a cat 5e cable to a cisco e3200(it reports its in gigabit mode)

but transfer rates are wayyyyy slow. thats why i looked at the speed/duplex settings in the hardware manager to try and force it to gigabit, thats when i noticed there is no setting for it

Title: Re: m68m-s2p rev 2.3
Post by: F5BJR on June 13, 2011, 05:04:53 pm

-
Transferts are at low speed between your computer and what ?

Pierre

Title: Re: m68m-s2p rev 2.3
Post by: wizeone on June 13, 2011, 06:03:52 pm

between my main computer duplex set to gigabit and to the computer with the m68m board.. 8 gig file only getting 24mbs transfer rate

Title: Re: m68m-s2p rev 2.3
Post by: F5BJR on June 13, 2011, 06:20:26 pm

-
At first time connect directly the 2 * computers and test the transfert speed

Pierre

Title: Re: m68m-s2p rev 2.3
Post by: wizeone on June 14, 2011, 12:51:50 am

ok i dont get your last statement.  last i knew you couldnt just directly connect 2 computers with a cat5(e) cable.

and to get back to the topic.  the settings from the control panel for the builtin network card do not have a setting for gigabit. so wich of the settings listed in the first post are for gigabit?