Official GIGABYTE Forum

Questions about GIGABYTE products => Motherboards with AMD processors => Topic started by: Scuttle on February 10, 2012, 05:34:35 pm

Title: Easytune 6 requires BIOS update. Whats your opinion?
Post by: Scuttle on February 10, 2012, 05:34:35 pm

Hi, more questions  ;D

I haven't been able to get ET6 to work correctly, in that it will only show one system fan when there are 2. According to Gigabyte Support, who have been helpful, I should be able to see both fans in ET6. They showed me a sreen clip of ET6 with the CPU, PSU and 2 SYS fans being monitored. I can see both fans operating correctly in BIOS health.

They have asked me to update the BIOS. I'm a bit concerned about updating the BIOS and risking knackering my system for the sake of running ET6. The MoBo shipped with F4 which will run all but 1 Phenom and none of the Bulldozers. Can't see myself laying out for a Bulldozer.

Whats your thoughts ?

Athlon II X4 645 3.1
GA-870A-USB3 BIOS  F4
Crucial Ballistix Sport 2x2GB DDR3 1600Mhz CL10 Unbuffered (running at 1300)
XFX ATI Radeon 6450 HD 625MHz 1GB passive
Be Quiet E9 StraightPower 400W
Thermalright Ultra-120 eXtreme Rev.C with 1 Scythe Slip Stream 120mm PWM
Samsung HD322GJ Spinpoint F4 320GB
CoolerMaster CM690 II - 2 standard case fans

Title: Re: Easytune 6 requires BIOS update. Whats your opinion?
Post by: Aussie Allan on February 12, 2012, 12:37:27 pm

  Hi Scuttle ..... sorry for the late reply ...... been busy, busy, busy

 Update the BIOS by all means ..... it can't hurt and can only fix the problem, increase compatability and possibly increase performance and stability  slightly ...... see if this fixes the problem ..... you may even have to un-install....and re-install ET6 ofter the Bios update ...... remember to tick "Clear DMI Data pool" ;)

  Aussie Allan

Title: Re: Easytune 6 requires BIOS update. Whats your opinion?
Post by: Dark Mantis on February 12, 2012, 12:51:48 pm

Hi

EasyTune 6 does require the latest BIOS file to be loaded in order to work properly. So go ahead and update it but make sure that you use QFlash not @BIOS and disable the Keep DMI Data on the homepage as you are doing it.

Title: Re: Easytune 6 requires BIOS update. Whats your opinion?
Post by: Scuttle on February 16, 2012, 05:44:03 pm

Hi

Sorry about the late response. My sole USB stick had been accidentally formatted so I had to find some free software to recover the files first. 

I updated this morning with no problems, now on F5f. Was all a bit nerve wracking but very straight forward.

ET6 now shows both the system fans - problem solved. It now shows 2 system temps running at 32deg.C and 21deg.C, would they be the north and south bridges? If so, which one is which?

Many thanks

Title: Re: Easytune 6 requires BIOS update. Whats your opinion?
Post by: Dark Mantis on February 16, 2012, 07:57:37 pm

Probably not, more likely the northbridge and the mainboard.

Title: Re: Easytune 6 requires BIOS update. Whats your opinion?
Post by: Scuttle on February 17, 2012, 07:43:51 pm

Thanks

Title: Re: Easytune 6 requires BIOS update. Whats your opinion?
Post by: autotech on February 18, 2012, 12:30:37 am

northbridge is 99% of the time the hotter one....lol    Used to use DFI and the northbridge always ran 45c to 60c which to me was way to hot.

Title: Re: Easytune 6 requires BIOS update. Whats your opinion?
Post by: Scuttle on February 18, 2012, 09:06:10 am

I asked Gigabyte who said

  System fan temperatures are being read from I/O chip as regular rule on GBT motherboards.

Looks like I got the right answer to the wrong question. They've been very helpful so I haven't hassled them again. Anyway, you guys are telling me that my temps are nice  and low so that's good enough for me.

Then again, maybe I'll just add a nice FD-FAN-140 on the side panel...................