Overclocking rookie here looking for advice
See my current setting below.
looking to get through 3DMark06 at 4.7ghz
Getting BSOD error Stop:0x 124
I understand this is memory setting or voltage.
Getting through 3DMark06 at 4.66, 30,500 3dmarks
any suggested setting for 4.7ghz???
>MB Intelligent Tweaker (M.I.T.)
>M.I.T Current Status......................[Press Enter]
>Advanced Frequency Setting...........[Press Enter]
CPU Clock Ratio ................................ [21x]
CPU Frequency 4.7GHz (224x21)
Advanced CPU Core Features...............[Press Enter]
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Disabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Bi-Directional PROCHOT ..................... [Enabled]
QPI Clock Ratio................................[auto]
QPI Link Speed .............................. 8.06GHz
Unicore Clock Ratio...........................[x16]
Uncore Frequency .......................... 3584MHz
>>>>>Standard Clock Control
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... [224]
Extreme Memory Profile (XPM)...........[Disabled]
System Memory Multiplier (SPD).........[8.0]
Memory Frequency (MHz) 1066..........[1792]
PCI Express Frequency (MHz) ........... [101]
>>>>>Advanced Clock Control
CPU Clock Drive ..............................[700mV]
PCI Express Clock Drive ................... [700mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]
>Advanced Memory Settings..........[Press Enter]
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [6.0]
Memory Frequency (MHz) 1066...........1320
Performance Enhance ...................... [Standard]
DRAM Timing Selectable (SPD) .......... [Quick]
Profile DDR Voltage............................1.5v
Profile QPI Voltage.............................1.175v
Channel Interleaving 6....................[Auto]
Rank Interleaving 4....................[Auto]
>>>>>>Channel A
Channel A Timing Settings..................[Press Enter]
>>>>> Channel A Standard Timing Control
CAS Latency Time 8..........[ 9]
tRCD 8..........[ 9]
tRP 8..........[ 9]
tRAS 20........[ 27]
>>>>> Channel A Advanced Timing Control
tRC 27........[Auto]
tRRD 4..........[Auto]
tWTR 4..........[Auto]
tWR 8..........[Auto]
tWTP 19........[Auto]
tWL 7..........[Auto]
tRFC 60........[Auto]
tRTP 4..........[Auto]
tFAW 20........[Auto]
Command Rate (CMD) 1..........[2]
>>>>> Channel A Misc Timing Control
B2B CAS Delay -..........[Auto]
Round Trip Latency 59........[Auto]
Channel A Turnaround Settings...........[Press Enter]
>>>>>Channel A Reads Followed by Reads
Different DIMMs 6.........[Auto]
Different Ranks 5.........[Auto]
On The Same Rank 1.........[Auto]
>>>>> Channel A Writes Followed by Writes
Different Dimms 6........[Auto]
Different Ranks 6.........[Auto]
On The Same Rank 1.........[Auto]
>Advanced Voltage Settings
******Mother Board Voltage Control******
Voltage Type Normal Current
>>> CPU
Load-Line Calibration [Standard]
CPU Vcore 1.22500V [1.56250V]
x Dynamic Vcore (DVID) +0.00000V Auto
QPI/Vtt Voltage 1.175V [1.395V]
CPU PLL 1.800V [1.500V]
>>> MCH/ICH
PCIE 1.500v [Auto]
QPI PLL 1.100v [1.440V]
IOH Core 1.100v [Auto]
ICH I/O 1.500v [Auto]
ICH Core 1.100v [Auto]
>>> DRAM
DRAM Voltage 1.500v [1.660V]
DRAM Termination 0.750v [Auto]
Ch-A Data VRef. 0.750v [Auto]
Ch-B Data VRef. 0.750v [Auto]
Ch-C Data VRef. 0.750v [Auto]
Ch-A Address VRef. 0.750v [Auto]
Ch-B Address VRef. 0.750v [Auto]
Ch-C Address VRef. 0.750v [Auto]
> Miscellaneous Settings
Isochronous Support [Enabled]
Virtualisation Technology [Enabled]
