Official GIGABYTE Forum

GA-890FXA-UD5 bios F6 info

autotech

  • 1553
  • 35
GA-890FXA-UD5 bios F6 info
« on: January 10, 2011, 03:55:03 am »
I am not sure why but if you have a  GA-890FXA-UD5  and you flash the bios to F6 then in the cpu multiplier you dont get half numbers anymore it goes whole numbers only.  Like from 16 to 17 to 18 not 16 to 16.5 to 17 to 17.5 like it used to. Just wanted to put this info out there so others dont get suprised.
GA-Z170X-UD5,Core i5-6600K,16 GIG,3200 ram ,2 X Corsair 240GB SATA III SSD, 500 gig HD,7 ult 64\, Rx-480 8gig\

Z97X-SOC GIGABYTE, I5 4670k, 16 gig 1600 ram, 240 gig sata3 SSD,1x 500HD/ R9 280x, corsair 650 RM PSU

GA-Z97X-Gaming G1,850 corsair,,DDR4 3200,240SSd,6950 video,850EVA

Christoph

  • 138
  • 2
Re: GA-890FXA-UD5 bios F6 info
« Reply #1 on: January 10, 2011, 04:29:41 am »
we know that

if you wanna have half numers then go back to F4

autotech

  • 1553
  • 35
Re: GA-890FXA-UD5 bios F6 info
« Reply #2 on: January 11, 2011, 01:09:45 am »
OR wait till F7 maybe. Was more of an informational post and not a gripe. Doesn't bother me at all. I just wanted anyone else that was considering flashing to F6 to know ahead of time. Only other difference i was able to tell was that with F4 i crashed 5 to 10 minutes into battlefield bad company 2 because of my overclock. I went back to 3.6 and 1600 ram and didnt crash and it was only that 1 game all other games ran fine but with F6 i am at 3.8 and 1600 ram and no crash.

Something got fixed there though i cant tell you what.
GA-Z170X-UD5,Core i5-6600K,16 GIG,3200 ram ,2 X Corsair 240GB SATA III SSD, 500 gig HD,7 ult 64\, Rx-480 8gig\

Z97X-SOC GIGABYTE, I5 4670k, 16 gig 1600 ram, 240 gig sata3 SSD,1x 500HD/ R9 280x, corsair 650 RM PSU

GA-Z97X-Gaming G1,850 corsair,,DDR4 3200,240SSd,6950 video,850EVA

Christoph

  • 138
  • 2
Re: GA-890FXA-UD5 bios F6 info
« Reply #3 on: January 11, 2011, 04:57:43 am »
really?

well thats some useful info...

thanks for the tip

Re: GA-890FXA-UD5 bios F6 info
« Reply #4 on: February 18, 2011, 07:16:22 am »
I have the Same setup basically. try running in windows basic for the game. or your settings in the bios are not quite right for optimum performance. Especially your memory tiiming.   if needed....here are some settings to help you get more out of the rig. also
ht ref clock: 214mhz
core speed 856mhz
nb speed 2354mhz
nb multiplier 11x
PCIe speed 105mhz
core multiplier 4x
hypertransport link: 2353mhz : max width in and out should be 16 bits

memory ocz  (ocz3g1600lv2g).Ungaged.... CAS latency clock: 8 clock...RAS to CAS delay: 8 clock...Command Rate:2T ...RAS active time: 23 clock..Row Cycle Time: 27 clock... Row Precharge time: 8 clock)
Write to read DIMM term: 2 clock) read to write DQS cont.: 6 clock) Write to Write timing: 4 clock) read to read timing : 4 clock) Write to read Delay: 4 clock) Write recovery time: 6 clock Read CAS to Precharge time: 4 clock) Refresh rate 7.8 us) Idle cycle limit :16 cycles) ..(DCC Enable: Disable seting!) DRAM termination 30ohms.) Row Refresh Cycle time 0,1,2,3, set to 110ns)
Voltages (targets set in bios): CPU VID: 1.40v) NB VID 1.1V) VCC18 core 1.85v) SidePort Memory 1.61cv) Memory Core 1.74v) VDDA25 Core 2.58v) NB Core 1.36v)
Windows 7  : Gigabyte GA-890GPA-UD3H  Processor  AMD Phenom(tm) II X4 965 Processor (oc to 3.85ghz) :Memory  8.00 GB 1633 (oc to 1750mhz) :Hard Drive  1.5 TB, WDC WD15EARS-00Z5B1 : Video  ATI Radeon HD 5770 850 mhz 1gig ( oc  910mhz/with onboard video engaged 256meg oc 1443mhz/similar to crossover