Official GIGABYTE Forum

GigaByte GA-990FXA-UD3/G.Skill 1866 mhz memory ??

jimdot

  • 38
  • 0
Re: GigaByte GA-990FXA-UD3/G.Skill 1866 mhz memory ??
« Reply #15 on: November 04, 2011, 09:08:00 pm »
P.S spwanasin. If you talk with GigaByte tech support & find out anything I would really appreciate you posting any new information here.
Once I get 4 good sticks and if I still have a problem THEN I will address tech support.

Jim

absic

  • *
  • 5815
  • 529
  • Never give up; Never surrender!
    • Bandcamp
Re: GigaByte GA-990FXA-UD3/G.Skill 1866 mhz memory ??
« Reply #16 on: November 05, 2011, 06:32:17 am »
Hi Jim,

basically you've got it right it's two or four sticks of RAM. And yes, before anybody says "Well I run my system with three sticks on-board" sometimes you can get away with doing so but it's not a good idea.

Sadly you will have to return ALL four sticks and have them replaced as they are sold as a matched kit.
Remember, when all else fails a cup of tea and a good swear will often help! It won't solve the problem but it will make you feel better.

absic

  • *
  • 5815
  • 529
  • Never give up; Never surrender!
    • Bandcamp
Re: GigaByte GA-990FXA-UD3/G.Skill 1866 mhz memory ??
« Reply #17 on: November 09, 2011, 01:45:37 pm »
I have been doing a bit more research into this and it has been noticed that on the GSkill website for these modules it states:
Quote
G.Skill guarantees 2 Dimms dual channel operation would reach announced specification.

check here: http://gskill.com/products.php?index=379

From this it would seem as if populating all four slots might be a problem and it would be a good idea to find out what GSkill's views on this subject are.

Remember, when all else fails a cup of tea and a good swear will often help! It won't solve the problem but it will make you feel better.

Re: GigaByte GA-990FXA-UD3/G.Skill 1866 mhz memory ??
« Reply #18 on: January 01, 2012, 08:53:05 am »
I have been battling this problem for 8 months. I have been through 3 sets of ram, 2 power supplies and now my 4th mb. Spent over 6 hours on the phone with Gigabyte techs and 2 hours with Corsairs techs. Conclusion? The gigabyte boards can not run 1866 ram period!!! I used 3 different GA 880 ud3 boards and now just tested on a 990 and it does not work! Buy Asus and be done with it! i plugged it in and it worked perfectly! not to mention using the exact same setup only changing MB from Gigabyte to asus I went from a 3.8 ghz OC to a Stable 4.2 on the asus. <- first time! I wasted 8 months of my life and numerous trips to the return line, to do what Asus's board did in less than 5 minutes!

hack

  • 2
  • 0
Re: GigaByte GA-990FXA-UD3/G.Skill 1866 mhz memory ??
« Reply #19 on: March 15, 2012, 03:38:31 pm »
I HAVE SAM PROBLEM The solution that i found is  put dram E.O.C.P to profile 2 then you have 1866 mhz and 1.5 vat
« Last Edit: March 15, 2012, 03:43:44 pm by hack »

TimM

  • 1
  • 0
Re: GigaByte GA-990FXA-UD3/G.Skill 1866 mhz memory ??
« Reply #20 on: December 10, 2012, 10:01:36 pm »
I have this same board, same problem, only I have G. Skill sniper 1866, I fixed the problem by going into the memory settings and changing it to 1866 speed, then going into the timings and changing it to what the memory specs said, mine were 9 10 9 28 , then changed the memory voltage from 1.6 that it was set to by the board, to 1.5 like the memory spec said it was. It fixed it for me, I'm running 1866 at my memory settings now. Hope this helps you.

My specs were way off set by MB they were 11 13 11 33 and 1.6 v so not sure what actually fixed it, and after 9 hours of dealing with it, I honestly don't care anymore, its running at 1866, so I'm good now. I kept getting the boot failures when only changing it to 1866 speed though, so might have to reset timings and go from 1.6 to 1.5 v to fix it.
« Last Edit: December 10, 2012, 10:07:30 pm by TimM »