EasyTune 8 not remembering settings.

[Svarog]

Gonna keep it short and simple.

Specs:

Intel Core i7 4770K
Gigabyte X87X-OC (F3)
Gskil ARES 2133 MHz
Zotac GTX 680 4GB
Creative X-Fi Titanium Fatal1ty Pro
Crucial M4 256GB (040H)
OCZ Vertex 120GB (1.7)
Samsung SpinPoint 1TB
SeaSonic Platinum 760
Windows 7 Ultimate 64-Bit

So i installed App Center followed by EasyTune. The Bios Fan Controls are set to Normal as the Manual says that allows control thru EasyTune. I Calibrate the Fans, setup my Fan Profile via the Advanced setting, click Apply and config EasyTune to retain the Smart Fan settings.

After rebooting everything has been reset to default.

[Gloup_Gloup]

Easy Tune 6 and other previosly version are bad sofware.

It cause many problems in system.

The best is to uninstall it completely and use other third party software.

Like Hardware monitor
http://www.cpuid.com/softwares/hwmonitor.html

PC Wizard
http://www.cpuid.com/softwares/pc-wizard.html

Hardware infos
http://www.downloadbestsoft.com/HWiNFO.html

[Svarog]

Sadly enough all those programs are just monitoring. I just want to set up a CPU Fan Speed profile.

I been using EasyTune on my X58A-UD7 for years without resetting issues.

[Gloup_Gloup]

Hi all,
He exist SpeedFan:
http://www.almico.com/sfdownload.php

http://img857.imageshack.us/img857/6291/speedfanb.jpg

[polypenko]

I have the same problem with Easy Tune.

Just not able to control the cpu fan correctly.

ga z87x ud5 i7 4770k

[polypenko]

Did some further testing.

Irrespective of the settings in the Bios the cpu fan runs on full throttle during start up and or entering the bios.

In order to get the cpu fan to throttle down I have to go into EASY Tune hit calibrate each and every time.

On my previous Gigabyte mother boards I most often did not even bother to use Easy Tune but used the bios
setting to reflect my preference.

On the z87x ud5h the bios setting do not seem to effect the Fan rpm settings, buggy bios?

[Gloup_Gloup]

Did some further testing.

Irrespective of the settings in the Bios the cpu fan runs on full throttle during start up and or entering the bios.

In order to get the cpu fan to throttle down I have to go into EASY Tune hit calibrate each and every time.

On my previous Gigabyte mother boards I most often did not even bother to use Easy Tune but used the bios
setting to reflect my preference.

On the z87x ud5h the bios setting do not seem to effect the Fan rpm settings, buggy bios?

Maybe because you have a CPU with Hyperthreading ... the Fan rpm are sensitive ....
The hyperthreading in BIOS is Enabled or Disabled?
This is just a question. Not for make a change in bios.

[Gloup_Gloup]

Hi for all, 

Notice for all,

Why you do not use SpeedFan?

http://forum.giga-byte.co.uk/index.php/topic,12574.msg82636.html#msg82636

[Svarog]

Never been able to get SpeedFan to work, it's way to complicated.

Since the Noctua NH-U14S (Push/Pull) is still silent at 1200 RPM i'm going for a more easy solution. Put the Fan Speed Reducer in between and keep the Bios Fan settings to Silent Mode

[polypenko]

My problem is solved with the kind help of GB Hamburg.

Apparantly my brand new Gelid 12cm 4 pin cpu fan is not compatible, mounted a Scythe 12cm and this
is running correctly.

Will monitor Easy Tune to see is my settings are rembered or also defaulted

[Gloup_Gloup]

Also make sure to calibrate the fans with easytune or it wont properly work.

[Svarog]

Nothing helps.

EasyTune just wont remember Fan profiles setup in the Advanced section.

[polypenko]

On my Z87x ud5 the Fan settings are correctly stored in Easy Tune.

Did you click on "Retain Smart Setting after reboot" in the preference box?





 

[Svarog]

Yep, checked that but after a reboot it has all been reset to default.

And that's with a clean install of Windows.

Perhaps EasyTune doesn't like the Noctua NF-A14 PWM fans.

[polypenko]

That be might the case, my 120mm Gelid fan ran full throttle.

For the time being I'm using a 120mm Scythe fan, trust a new bios will solve these issues.