Official GIGABYTE Forum

Looking for stable settings for Corsair Vengeance CMZ8GX3M2A1600C9

Dave997

  • 14
  • 0
I have 16gigs (4x4gig) of Corsair Vengeance CMZ8GX3M2A1600C9

I have been having problems waking from sleep mode as well as some memory management and PFN_LIST_CORRUPT BSODs. I've tried the 6 most recent drivers for my video card and have the same issues so im inclined to think that it might be my memory timings and voltages.


My motherboard is an unclocked GIGABYTE GA-X79-UD3 with the latest F10 BIOS. When I load Optimized defaults my RAM timings are 9-9-11-24 1333mhz 1.5v and 1t command rate. I looked up my rams serial number and went to the Corsair website and changed my BIOS's default memory timings to the recommend 9-9-9-24 1.6v (i decided to raise the voltage since im running 4x4, im not sure if that will help it or not) enabled XMP profile which raise my frequency to 1600mhz and I also changed command rate to a more stable 2t. Ever since I did this I went from about a 50% chance to resume from S3 sleep mode to a 90-95% chance to resume, so those settings did make progress. My BSOD's while gaming and surfing the web have also been greatly lowered.

My main question is about the voltages and timings, what do you think of them as far as stability? Would you have any recommendations as far as increasing stability? Thanks.




Dark Mantis

  • *
  • 18405
  • 414
  • 10typesofpeopleoneswhoknow binaryandoneswhodont
    • Dark Mantis
Re: Looking for stable settings for Corsair Vengeance CMZ8GX3M2A1600C9
« Reply #1 on: April 17, 2012, 09:01:52 pm »
Hi

Firstly I would increase the memory voltage a touch to about 1.55v instead of the default.

You said about getting BSODs but didn't give the all important STOP code from them. Can you post them here please.
Gigabyte X58A-UD7
i7 920
Dominators 1600 x6 12GB
6970 2GB
HX850
256GB SSD, Sam 1TB, WDB320GB
Blu-Ray
HAF 932

Gigabyte Z68X-UD5-B3
i7 3770K
Vengeance 1600 16GB
6950 2GB
HCP1200W
Revo Drive x2, 1.5TB WDB RAID0
16x DLRW
StrikeX S7
Full water cooling
3 x 27" Iiy

Dave997

  • 14
  • 0
Re: Looking for stable settings for Corsair Vengeance CMZ8GX3M2A1600C9
« Reply #2 on: April 17, 2012, 09:07:43 pm »
Hi

Firstly I would increase the memory voltage a touch to about 1.55v instead of the default.

You said about getting BSODs but didn't give the all important STOP code from them. Can you post them here please.

hi :) I increased voltage from 1.5 to 1.6 as far as the BSODs go they are PFN_LIST_CORRUPT 0x4E



Edit: I just read that my CPU-VTT which is 1.06 cant have the VDIMM setting higher than .5 above it , so 1.06 +.5 is 1.56 so I followed your advice and set it back to 1.55 instead of 1.6 where it was. If i move the CPU-VTT up a few notches to maybe 1.1 so i can set my VDIMM voltage to 1.6 do i need to change anything else? Im using this guide http://www.masterslair.com/vcore-vtt-dram-pll-pch-voltages-explained-core-i7-i5-i3/#vtt-aka-imc-qpivtt-qpidram
« Last Edit: April 18, 2012, 01:03:08 am by Dave997 »

Dark Mantis

  • *
  • 18405
  • 414
  • 10typesofpeopleoneswhoknow binaryandoneswhodont
    • Dark Mantis
Re: Looking for stable settings for Corsair Vengeance CMZ8GX3M2A1600C9
« Reply #3 on: April 18, 2012, 12:51:02 pm »
Yes I think I would increase the CPU voltage a touch which will also allow you movement in the memory voltage too.
Gigabyte X58A-UD7
i7 920
Dominators 1600 x6 12GB
6970 2GB
HX850
256GB SSD, Sam 1TB, WDB320GB
Blu-Ray
HAF 932

Gigabyte Z68X-UD5-B3
i7 3770K
Vengeance 1600 16GB
6950 2GB
HCP1200W
Revo Drive x2, 1.5TB WDB RAID0
16x DLRW
StrikeX S7
Full water cooling
3 x 27" Iiy